Veneer Dryer Temperature Controller-manufacture,factory,supplier from China

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:First, warm the furnace: The high-temperature-resistant material poured into the burner is very thick and needs to be dried out of the moisture in the furnace so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

In 2020,a friend from Singapore successfully cooperated with us.This is a friend from a long time ago.After adding our contact information,he became very interested in our veneer dryer,but he was worried about the output of the machine.never negotiated a cooperation,and finally,after visiting our factory,the customer dispelled his concerns and showed great interest in our patented biomass burning furnace,because this furnace can reasonably use the scraps from the rotary cutting Combustion,rational use of resources,and will not produce environmental pollution,smog and other effects,and finally

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:Warming furnace: The high-temperature-resistant material poured into the burner is very thick, and the moisture in the furnace needs to be dried out so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

After purchasing one of our veneer dryers, our Zimbabwean customers have recently purchased a second veneer dryer , which is currently being installed, along with our biomass burners, by our engineers The installation is carried out under the guidance, and the customer feedback is very good. If there is a need in the future, we will continue to buy our equipment. Thank you for your trust in us.

The shine veneer dryer has the characteristics of large drying output, good effect, and easy maintenance. It has been unanimously recognized by customers and has been widely used. However, some customers always report that the efficiency of the wood chip drying equipment is not high. This is due to insufficient It is caused by paying attention to the details in the work. So what are the precautions when using veneer drying equipment?We always hope that the veneer can dry quickly, so we set the temperature to be very high and the temperature rises very quickly.

Recently, due to the impact of the epidemic, many customers were unable to go to the site to see the equipment. We organized an online viewing site, and our engineer gave a comprehensive explanation of the veneer dryer in live video. Finally, the questions raised by customers were all Answer one by one, if you also want to see the scene of equipment operation, please feel free to contact us.

Many people may encounter the problem of veneer jamming when using the roller veneer dryer. In order to avoid this problem, the following suggestions can be taken: First, keep the equipment clean, clean the dust collector and exhaust duct, and minimize the accumulation of dust; second, do a good job of adjusting the equipment, reduce the friction and wear of the equipment, and regularly check the status of the roller bearings; finally, pay attention to the control of drying temperature and humidity to avoid excessive temperature and humidity, which will cause veneer deformation and jamming.

These are two sets of 2 deck veneer dryers from our old South African customer.They were installed and guided by our engineers.The customer was very satisfied after buying one of our machines,and then bought the second one.Now Both are in normal use, and the customer feels that the equipment is very good,and the operation is convenient,and the dried veneer is very flat.We are very grateful to South African users for their support.We will continue to work hard in the process of research and development and production to complete the task with quality and quantity.We are also very welcome to vis

Shine veneer dryers are available with outputs ranging from a dozen cubic meters to more than a hundred cubic meters. They have their own heat source biomass burner; they can directly burn waste bark to save fuel costs (it can also be used with other heat sources). The newly upgraded dryer reduces the power of the whole machine by 38%, achieving true energy saving. The automatic control system is adopted to automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content to achieve the ideal drying effect.